Boost Evo Knowledge Base

Boost Evo Introduction

For the ultimate dabbing experience, the Dr. Dabber Boost Evo is your one stop shop. Its temperature control and ease of use will make the Evo your everyday concentrate rig. Dr. Dabber’s award-winning vaporizers have evolved to this.

The Basics

Boost Evo Unboxing

Achieving the perfect dab every single time you use your vaporizer is a metric that is often overlooked, but most vaporizers on the market have little or no temperature control, calibrated to continuously heat up until a certain point in time when it cuts off. This leads to a ridiculous variance in the temperature you are dabbing at, which doesn’t make sense to us. The Boost Evo has a patent pending temperature control sensor built in, unlike anything else on the market. This means that when you are dialed in, you are DIALED IN. With six heat settings that have been calibrated with the help of customer feedback from tens of thousands of Boost users, you can rely on your Boost Evo to be consistent every single time.

Pair that technology with a custom quartz dish, interchangeable glass, spectacular RGB ambient lighting and surprisingly long battery life for such a portable device, the Dr. Dabber Boost Evo is truly the next generation of the e-Rig. Available in two colors - Moon White & Eclipse Black.

Features:

6 Temperature Settings - 500-750° F

11 Second Heat Up Time

Revolutionary magnetic Quartz e-Chamber with built-in temperature sensor

Quick Connect Adapter with airflow release

Straight quartz to glass vapor pathway

Enhanced ergonomics with grip pads

5 RGB light modes plus Stealth Mode for discreet dabbing

Exceptional battery life with built-in protection against over voltage and short circuits

60+ hits on a single charge

20 or 40 second hold time

Pass through USB-C charging

Auto shutoff after 15 minutes

Durable and protective carrying case included

1 Year Warranty

Boost Evo Kit Contents:

Dr. Dabber Boost Evo

Boost Evo Quartz e-Chamber

Glass Water Attachment

USB-C Charger

Quick Connect Adapter

Loading Tool

How to use your Boost Evo

Boost Evo User Guide

Load your concentrates directly on the bottom heating plate for best results. You may load up to 1/2 the e-Chambers capacity, but we recommend a rice sized amount at a time for most users.

1. Fill glass attachment with water and attach to the quick connect adapter. Make sure glass is fully pushed down on to adapter.

2. Prepare your product and load e-Chamber directly on the bottom heating plate.

3. Once your product is properly loaded, reconnect glass attachment and quick connect adapter to the Boost Evo unit.

4. Turn unit on, select heat setting, and depress power button for 3 seconds to start a heating cycle. The unit will vibrate once the heating cycle has started and will illuminate RED while heating, then it will vibrate again and illuminate GREEN notifying you that optimal temperature has been reached and the unit is ready to start your hit. Take long, slow drags for best results.

5. Press airflow release button to clear glass attachment. Enjoy Vapor!

Quick Tips & Tricks

You may use the airflow release button to manipulate the airflow in the heating chamber creating more or less vapor density. Flutter your finger over the air intake hole and fully depress the button every few seconds to increase vapor density.

We recommend filling your glass attachments with water just above the perc holes. Fill the water from the mouthpiece until it has reached the appropriate level. Over filling the attachment may cause splash back or leak in to your e-Chamber. Using water in the glass attachment cools and filters vapor for a cleaner hit.

Do not dry burn e-Chambers. This will help extend the life of these parts. There should always be a small amount of oil in the e-Chamber while in use. Your e-Chambers will begin to season overtime, allowing them to produce more vapor with less concentrates. e-Chambers are not covered under warranty as they are disposable components and will need to be replaced over time. We recommend between 4-12 months depending on usage.

Changing your e-Chamber is simply just another part of successful e-Rig care. Here are some signs that your e-Chamber may need to be changed:

-It is visually dark or damaged.

-The dish is cracked or broken.

-You are experiencing a “burnt” taste, even after thoroughly cleaning your device.

-Your e-Chamber is having leakage issues.

-You are experiencing decreased vapor production.

When installing a new e-Chamber , your Boost Evo unit must be recalibrated with the new e-Chamber before first use . This is accomplished in the following procedures:

* Unit must be turned OFF and unplugged for 15 minutes prior to the next step in recalibration to ensure that the main unit and the e-Chamber are at the same temperature.

* While the unit is OFF, press the power button 4 times with the user holding down the button on the 4th press. If lights blink RED (x3) then recalibration did not work, and should be attempted again. If lights blink WHITE (x3) then recalibration was successful.

* Unsuccessful recalibration may be the result of: a difference in temperature between the e-Chamber and the Main Unit while a recalibration is attempted, unclean electrode connections, or an e-Chamber not properly installed in the unit. These need to be resolved and several recalibration attempts may be necessary before a successful recalibration.

Other Features

Party Mode:

While the unit is Off, press and hold the power button to change the time the unit stays on temperature. The LEDs will blink 2 times to indicate a hold time of 20 seconds, or 4 times to indicate a hold time of 40 seconds.

Glow Mode:

Press the power button 4 times to turn the Glow Mode On/Off. In Glow Mode, the LEDs will illuminate in a decorative pattern. Press the power button 2 times to cycle between the five patterns.

Stealth Mode:

Press the power button 2 times while Glow Mode is off to turn Stealth Mode On/Off. LED illumination is reduced when using Stealth mode and only the power button will illuminate.

Temperature Settings

Heating profile breakdown (in approximation): Purple: 500 Blue: 550 Cyan: 600 Green: 650 Orange: 700 White: 750. Switching between each heat setting is as simple as clicking the button 3 times. The lights on the button and unit will indicate which heating profile you have entered (only the button illuminates in stealth mode). Lower temperature settings are recommended for maximizing flavor, and higher temperatures are recommended for maximizing vapor production.

We do not recommend going higher than the Green/650 setting unless you are using large amounts of product. Higher heat settings will burn through smaller loads quickly and produce minimal vapor.

*When using the Boost Evo Sapphire e-Chamber, we do not recommend setting the temperature higher than the Green setting. Higher heat settings may cause excessive chazzing. Let the Sapphire e-Chamber cool down for about 20 minutes after running 2-3 back to back heating cycles to avoid issues with this e-Chamber.*

The Boost Evo Carrots Edition offers different heat settings. Check out the Boost Evo Carrots Edition User Manual for temp settings on this unit.

Charging your Boost Evo

We recommend charging your device fully before initial use. The unit will blink the color of the current heat setting and vibrate 3 times when the battery needs to be recharged. The Boost Evo uses a USB-C charging cable. Charging your unit is easy, just plug your charging cable in to a USB port (or AC Adapter for faster charging) and insert the other end of the cable in to the charging port on the back of the unit. Try not to use too much force. The charger indication LEDs (under power button) indicate the battery status. The charger indication LEDs will pulse white to indicate charging, and solid white to indicate fully charged. The battery lasts for approximately 40-60 heating cycles and takes about 1 hour to fully charge. We only recommend charging your unit once it reaches less than a 20% charge (One LED) and removing your unit from the charger as soon as it is fully charged. This will help extend the overall lifespan of your battery. Leaving your unit plugged in for extended periods will shorten the lifespan of the battery. This battery also offers pass through charging, which means you may use the unit while it charges.

*The Boost Evo will not charge off a high wattage power adapter, such as a laptop charger. Please use a phone (AC adapter) or a USB port on a computer or similar device to charge the unit.*

Cleaning your Boost Evo

Cleaning Guide

We recommend cotton swabbing e-Chambers after every use to extend the life and flavor of these parts. Use a dry cotton swab to mop up any leftover residue. While the e-Chamber is still warm, use a cotton swab dipped in ISO to remove any stubborn blemishes. Chazzing/Staining may occur over time, but this is normal with all dab rigs and should not compromise flavor or function.

Remove the glass attachment and quick connect adapter from the unit. Using a cotton swab or paper towel dipped in ISO, clean any residue in and around the heating chamber/e-Chamber, dab tool, and quick connect adapter. Let all parts air dry completely before use.

To clean glass attachments, fill with ISO and shake vigorously until all blemishes are removed. You may need to repeat this step. Completely rinse with water and let air dry.

*Do NOT soak Boost Evo e-Chambers in ISO or any other liquid. *

Compatible Items

The Boost Evo is compatible with the Boost Evo Quartz e-Chamber, Boost Evo Sapphire e-Chamber, Boost Evo Quick Connect Adapter, and Boost Evo Silicone Mat.

Glass options compatible with the Boost Evo: Boost Evo Replacement Glass Attachment, Boost Evo TDE Sidewinder, Boost Evo: TDE J-Perc, Boost Evo: TDE Ball Rig, Boost Evo: TDE Whip Attachment, Boost Evo TDE Half Cap, Boost Evo Hemisphere, Boost Evo Hive Ball, and Boost Evo Egg.

When using the Boost Evo Sapphire e-Chamber, we do not recommend setting the temperature higher than the Green setting. Higher heat settings may cause excessive chazzing. Let the Sapphire e-Chamber cool down for about 20 minutes after running 2-3 back to back heating cycles to avoid issues with this e-Chamber.

When using TDE glass attachments, make sure you replace the silicone seal on your QCA (Quick Connect Adapter) with the TDE silicone seal that is included with these glass attachments. This seal will reduce airflow coming from the QCA and allow the TDE Carb Cap to function correctly.

The USB-C Charging Cable (compatible with the Stella, XS, and Boost Evo units) and Dab Tool are also sold separately.

Troubleshooting

Make sure battery is fully charged and unit is powered on with 5 rapid clicks of the power button. The unit is ON when the lights illuminate.

Make sure all connections points between the e-Chamber and unit are clean. Use a cotton swab dipped in ISO to clean connection points.

Recalibrating the unit (recalibration instructions below) will usually solve most issues with the Boost Evo.

Boost Evo units with serial number starting at 03 and above error codes

3 RED Blinks: Recalibration attempt unsuccessful. Make sure unit is fully cooled and attempt recalibrating the unit again.

3 WHITE Blinks: Open circuit/no e-Chamber. Remove e-Chamber from the unit and clean all connection points between the e-Chamber and the unit with a cotton swab and ISO alcohol. Make sure e-Chamber sits flush on the unit. e-Chamber replacement may be needed.

3 PINK Blinks: Clean connections between e-Chamber and unit. Fully clean e-Chamber. e-Chamber replacement may be needed.

3 ORANGE Blinks: Clean connections between e-Chamber and unit. If you continue to have issues, please contact support.

Boost Evo units with serial number starting at 02 or below error codes

3 RED Blinks: Recalibration attempt unsuccessful. Make sure unit is fully cooled and attempt recalibrating the unit again.

If you continue to have issues after the above tips, we recommend recalibrating your unit and e-Chamber. This is accomplished in the following procedures:

* Unit must be turned OFF and unplugged for 15 minutes prior to the next step in recalibration to ensure that the main unit and the e-Chamber are at the same temperature.

Recalibration video for reference.